1997 Specialty Products Parts

Choose a Make for your 1997 vehicle


Showing 1 - 6 of 6 products
Image
SKU
Product
Rating
Price

Specialty Products
  • TACOMA UCAS (PAIR)
  • Camber: + or -2 degrees; Caster: 0 degrees TO +4 degrees; ADJUSTABLE
  • Product Attributes:
    • California Proposition 65: Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer, Birth Defects, Or Other Reproductive Harm.
  • Improve droop travel, drivability and tire wear as well as adjusting tire position in your wheel well with SPC's adjustable front upper control arms for Tacomas, PreRunners and 4-Runners. Featuring our long life maintainable ball joint and SpecRide bushings, this arm is designed to correct alignment angles while maintaining factory ride quality. SPC's integrated tubular and cast steel design provides the strength and durability needed for the most demanding environments. These remove and replace arms are available in pairs for lifted and off-road applications.

    Get more droop travel: SPC's arm has improved clearance to get around the spring bucket when the arm droops, eliminating arm to frame contact on lifted trucks. The maintainable ball joint has an oversized ball and allows more than 80° of articulation to ensure it never binds. SpecRide bushings have free pivot to eliminate any chance of bushing failure seen in many high travel suspensions.

    Get your drivability and tracking back:When you lift your truck you affect caster and camber. SPC's arm have +1° of caster built into them. Using its patented ball joint design the arm will get you 0° to +4° of caster and ±2° of camber.

    Get your tire where you want it in the wheel well: Use adjustment in the control arm and on the OE lower cams to maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming.

    Do you need replacement cams for the lower control arm? Check out SPC p/n 25430, which will replace corroded cam bolt assemblies.

Additional Fitment Information:
Vehicle Position Drive Type
1997 - Toyota Tacoma Front Upper 4WD

Specialty Products
  • TACOMA UCAS (PAIR)
  • Camber: + or -2 degrees; Caster: 0 degrees TO +4 degrees; ADJUSTABLE
  • Product Attributes:
    • California Proposition 65: Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer, Birth Defects, Or Other Reproductive Harm.
  • Improve droop travel, drivability and tire wear as well as adjusting tire position in your wheel well with SPC's adjustable front upper control arms for Tacomas, PreRunners and 4-Runners. Featuring our long life maintainable ball joint and SpecRide bushings, this arm is designed to correct alignment angles while maintaining factory ride quality. SPC's integrated tubular and cast steel design provides the strength and durability needed for the most demanding environments. These remove and replace arms are available in pairs for lifted and off-road applications.

    Get more droop travel: SPC's arm has improved clearance to get around the spring bucket when the arm droops, eliminating arm to frame contact on lifted trucks. The maintainable ball joint has an oversized ball and allows more than 80° of articulation to ensure it never binds. SpecRide bushings have free pivot to eliminate any chance of bushing failure seen in many high travel suspensions.

    Get your drivability and tracking back:When you lift your truck you affect caster and camber. SPC's arm have +1° of caster built into them. Using its patented ball joint design the arm will get you 0° to +4° of caster and ±2° of camber.

    Get your tire where you want it in the wheel well: Use adjustment in the control arm and on the OE lower cams to maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming.

    Do you need replacement cams for the lower control arm? Check out SPC p/n 25430, which will replace corroded cam bolt assemblies.

Additional Fitment Information:
Vehicle Position Drive Type
1997 - Toyota Tacoma Front Upper 4WD

Specialty Products
  • 1-1/2° CAMBER/CASTER SLEEVE
  • 1- 1/2 degrees SLEEVE
  • Product Attributes:
    • California Proposition 65: Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer, Birth Defects, Or Other Reproductive Harm.
  • These popular sleeves are widely used to adjust caster and/ or camber on many Ford and Mazda RWD & 4WD trucks. To install, simply loosen and remove upper ball joint pinch bolt. Remove top snap ring if one is present. Use 77880 or 88830 sleeve puller to remove the existing sleeve. To split camber and caster adjustment, rotate sleeve 45°. Save time during alignment, use 23199 zero degree sleeve to determine initial readings, then install correct sleeve. Note: Sleeves adjust to a smaller degree on Ford andMazda 4WD light trucks/SUVS.

Additional Fitment Information:
Vehicle Position Drive Type
1997 - Ford E-350 Econoline Club Wagon Front Upper RWD

Specialty Products
  • 1-1/2° CAMBER/CASTER SLEEVE
  • 1-1/2 Degrees SLEEVE
  • Product Attributes:
    • California Proposition 65: Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer, Birth Defects, Or Other Reproductive Harm.
  • These popular sleeves are widely used to adjust caster and/ or camber on many Ford and Mazda RWD & 4WD trucks. To install, simply loosen and remove upper ball joint pinch bolt. Remove top snap ring if one is present. Use 77880 or 88830 sleeve puller to remove the existing sleeve. To split camber and caster adjustment, rotate sleeve 45°. Save time during alignment, use 23199 zero degree sleeve to determine initial readings, then install correct sleeve. Note: Sleeves adjust to a smaller degree on Ford andMazda 4WD light trucks/SUVS.

Additional Fitment Information:
Vehicle Position
1997 - Mazda B2300 Front Upper

Specialty Products
  • 1-1/2° CAMBER/CASTER SLEEVE
  • 1- 1/2 degrees SLEEVE; Dana 35
  • Product Attributes:
    • California Proposition 65: Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer, Birth Defects, Or Other Reproductive Harm.
  • These popular sleeves are widely used to adjust caster and/ or camber on many Ford and Mazda RWD & 4WD trucks. To install, simply loosen and remove upper ball joint pinch bolt. Remove top snap ring if one is present. Use 77880 or 88830 sleeve puller to remove the existing sleeve. To split camber and caster adjustment, rotate sleeve 45°. Save time during alignment, use 23199 zero degree sleeve to determine initial readings, then install correct sleeve. Note: Sleeves adjust to a smaller degree on Ford andMazda 4WD light trucks/SUVS.

Additional Fitment Information:
Vehicle Position Drive Type
1997 - Ford Ranger Front Upper 4WD

Specialty Products
  • 1-1/2° CAMBER/CASTER SLEEVE
  • 1-1/2 Degrees SLEEVE; Dana 35
  • Product Attributes:
    • California Proposition 65: Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer, Birth Defects, Or Other Reproductive Harm.
  • These popular sleeves are widely used to adjust caster and/ or camber on many Ford and Mazda RWD & 4WD trucks. To install, simply loosen and remove upper ball joint pinch bolt. Remove top snap ring if one is present. Use 77880 or 88830 sleeve puller to remove the existing sleeve. To split camber and caster adjustment, rotate sleeve 45°. Save time during alignment, use 23199 zero degree sleeve to determine initial readings, then install correct sleeve. Note: Sleeves adjust to a smaller degree on Ford andMazda 4WD light trucks/SUVS.

Additional Fitment Information:
Vehicle Position Drive Type
1997 - Ford Ranger Front Upper 4WD
Showing 1 - 6 of 6 products

Loading...